大学英语词汇短语释义解析及例句 compound die
释义：
compound die 复式压模; [机] 复合模; [机] 复合冲模
例句：
The first set is blanking and punching compound die.
第一组是消隐和冲压复合模。
The structure and machining process of plane diffluent compound die are introduced.
介绍了平面分流组合模的结构和加工工艺。
The design describes the structure of compound die stamping flip-chip design and working process.
本次设计阐述了冲压倒装复合模的结构设计以及工作过程。
In addition, both the working process of compound die and questions required attention are stated.
同时也阐述了复合模工作过程及注意事项。
Analyzed press technology characteristics of vent-windows of the car side board, designed a lancing-drawing compound die.
分析了车厢侧板零件通风窗冲压加工的工艺特点，设计了一副针对该零件加工的切口拉伸复合模。
Adopting once punching process and using fewer cost and worse plasticity leftover material finish twice drawing of compound die.
分析了小圆角圆筒件的成形工艺性，利用成本较低、塑性较差的角料，采用一次冲压工序完成二次拉伸的复合模。
Besides using nitrogen spring is discussed. I give another resolving method in improving the plane tolerance of compound die part.
并且对氮气弹簧的应用进行了论述，对满足多工位级进模中零件的平面度要求提出了另一种解决方法。
Through the analysis of forming technology of regulator of left chair, the method of using two sets of compound die is put forward.
通过对左座椅调整器的成形性工艺分析，提出了采用两套复合模结构的方法，并介绍了模具的具体结构及模具工作过程。
The application of the Shared plate technology effectively lowered the cost of the compound die and shortened the manufacturing cycle.
共用模板技术的应用，有效地降低了复合模成本并缩短了制造周期。
Improved properly such mechanisms as the location, stripping and scraps treatment, the common compound die was satisfied the need of the automatic stamping.
对普通复合模的定位、卸料以及废料处理等装置加以适当改进，满足了自动冲压的需要。
This paper analyzed technological peculiarities on the step part, designed a drawing and extruding compound die. It can improve the part quality and benefit.
通过分析零件的工艺特点，设计了拉伸挤压复合模，不仅可提高零件质量，而且可提高生产效率。
This paper put forward a new kind of compound die mechanism which is a combination of the link mechanism and hydraulic, and design of a new energy-saving plastic equipment.
因此本文提出了一种以连杆机构与液压相结合的执行机构，在此基础上设计出了一种新型的节能塑封设备。
Mainly introduced the detailed structure and working process and the technology analysis of the blanking-drawing-extruding compound die for the stainless steel whistle pot cover.
主要介绍了不锈钢球形响壶盖的落料、拉伸、挤边复合模的详细结构、模具工作过程、工艺分析。
The structural design, design parameters, material chosen and manufacture process of multi-pinhole compound die of main printed circuit board for large screen color TV are introduced.
介绍大屏幕彩色电视机主印制板多小孔复合模的模具结构、设计参数、材料的选用和制造工艺等。
The main points for the design of the compound die were introduced. The compound die has prominent advantages on the production of series products and on speeding up the production cycles.
通过介绍复合模的设计及要点，阐明了复合模对于系列化产品的生产，加快产品的投产周期，具有显著的效果。
Then layout design and various process forces of calculation is introduced. Finally drawing and extrusion compound dies is adopted to make die structure better rationalization and effectiveness.
并进行了排样设计和各种工艺参数的计算，最终采用拉深、挤边复合模具，可使模具结构更为合理而有效。
According to parts character, a pair of assembled punching, blanking compound die punching is designed, die structure is introduced, and assembled carling compound die structure is stated as well.
根据零件特点设计了一副组合式的冲孔、落料复合模冲压两种产品，介绍了模具结构，论述了组合式纵梁复合模的结构特点。
The structure, main design parameters and work process of the compound die installed on single action press and working for blanking and drawing with constant blank holder pressure were presented.
介绍了用于单动压力机的新型恒压边力落料拉伸复合模的结构及主要设计参数和模具工作过程。
A curling compound die for the hinge used for the plate-bending machine was introduced. The structure characteristics of the die and the attention problems in the design of the die were discussed.
介绍了一种适用于折板机的铰链卷圆成形复合模，讨论了该模具的结构特点和设计中应注意的问题。
Through the analysis of forming technology of regulator of left chair, the method of using two sets of compound die is put forward. The specific die structure and its work pro - cess are introduced.
通过对左座椅调整器的成形性工艺分析，提出了采用两套复合模结构的方法，并介绍了模具的具体结构及模具工作过程。
The bending and pressing convex forming compound die for locking spring is designed, the die structure and pressing process are introduced, the product quality and production efficiency are improved.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。提高了产品质量以及生产效率。
