大学英语词汇短语释义解析及例句 adhesive wear
释义：
adhesive wear [机] 粘着磨损
例句：
The main wear mechanism is adhesive wear and abrasive wear.
该材料的主要磨损机制为粘着磨损和磨粒磨损。
Oxidation and adhesive wear of the coating is lighter than that of the steel.
钢的氧化磨损和粘着比涂层严重。
Bat a decisive factors of ring failure are the adhesive wear and fatigue wear.
而钢领失效的决定性因素是粘着磨损和疲劳磨损。
The main wear mechanisms are oxidation wear, adhesive wear, and abrasive wear.
主要磨损机制为氧化磨损、粘着磨损和磨粒磨损。
The wear mechanisms during dry sliding process are oxidation wear and adhesive wear.
在干滑动摩擦过程中，磨损机制主要为氧化磨损和粘着磨损。
Adhesive wear and surface - fatigue wear are the two major wear forms in rail steel.
粘附磨损和疲劳磨损是轨钢的主要磨损形式。
The wear mechanism of the nanotube layers involved abrasive wear, fatigue wear, adhesive wear and oxidative wear.
纳米管层的磨损机理主要为磨粒磨损、疲劳磨损、粘着磨损和氧化腐蚀磨损。
There are five forms of wear and wear: abrasive wear, erosive wear, adhesive wear, fatigue wear and corrosive wear.
磨损有五种磨损形式：磨料磨损、冲蚀磨损、粘着磨损、疲劳磨损和腐蚀磨损。
The textured surfaces exist oxidation wear, abrasive wear and adhesive wear in the condition of line contact rolling.
在线接触滚动过程中，存在氧化磨损、磨粒磨损和黏着磨损。
The results shown that the slurry erosion wear of adhesive coating is composed of adhesive wear and antiwear filler wear.
结果表明，这种涂层的冲蚀磨损是由粘结剂的磨损和抗磨填料的磨损所组成；
The main wear mode of PPS is changed from adhesive wear into abrasion wear with the addition of PTFE and kaolin nanoparticles.
PTFE和纳米高岭土的加入使PPS的主要磨损方式由粘着磨损转变为磨粒磨损。
An adhesive wear model based on fractal parameter is derived on the grounds of adhesive wear theory by modifying the M-B fractal contact model.
在对M - B接触分形模型改进的基础上，根据阿查得粘着磨损理论导出了基于分形参数的粘着磨损模型。
The abrasive wear, fatigue wear and adhesive wear are the main factors causing the excess wear and breaking of the driving chain on drilling RIGS.
磨料磨损、疲劳磨损和胶合等是引起石油钻机传动链条磨损超限，承载；能力降低，最后导致链条断裂破坏的主要原因。
The main wear mechanism of MoSi 2 material is fatigue wear under the lower loads, while adhesive wear is the main mechanism under the higher loads.
低载荷下的磨损机制以疲劳磨损为主 ，高载荷下的磨损机制主要表现为粘着磨损。
The failure mechanism of journal bearing of roller cone bit is analyzed, the failure type is adhesive wear, and main factors affecting the adhesive wear are analyzed.
分析了牙轮钻头滑动轴承失效的机理，论证了牙轮钻头滑动轴承失效形式主要为粘着磨损，分析了影响轴承粘着磨损失效的主要因素。
In calf serum medium, the wear mechanism of fretting is mainly adhesive wear, fatigue wear and the weakening effect of solution molecules on the bone cement matrix under stress.
骨水泥在小牛血清介质中微动磨损的损伤机制主要为黏着磨损和疲劳磨损，溶液分子在应力作用下对骨水泥基体有削弱作用。
The wear rate initially increases and then decreases with sliding distance increasing in all tested materials, wear mechanism during dry sliding process is oxidation wear and adhesive wear.
干滑动摩擦磨损率随磨损滑移距离的增加先增加而后逐渐降低，磨损机制主要为粘着磨损和氧化磨损。
